Booking today · Houston service windows 9–12 · 1–4 · 4–7 Independent GE specialists · Licensed & insured Mon–Fri 7:00 AM - 8:00 PM · Sat 8:00 AM - 6:00 PM
(713) 547-5545 Arrange a Repair
Error code · Water Heater

GE GeoSpring First-Generation GEH50DEED Code F-E: Discharge temperature over limit

F-E on the first-generation GE GeoSpring GEH50DEED hybrid water heater, built roughly 2009 to 2012, tells you that the discharge temperature went above its limit. That reading is taken where hot refrigerant leaves the compressor, and…

High · stop use, call now
Arrange a Repair(713) 547-5545
Code
F-E
Appliance
Water Heater
Brand
GE
Warranty
30-day workmanship

What F-E means

F-E on the first-generation GE GeoSpring GEH50DEED hybrid water heater, built roughly 2009 to 2012, tells you that the discharge temperature went above its limit. That reading is taken where hot refrigerant leaves the compressor, and the control stops the heat pump when it runs too hot to protect it. You see F-E on the display. Hot water may continue from the electric elements. In this generation, F-E is a high-temperature protection stop, unlike the later 2014-2016 sensor codes.

Common causes of F-E

  • Airflow restrictions that make the compressor run hot
  • Discharge temperature sensor accuracy
  • Expansion valve and refrigerant flow
  • Fan operation
✓ One safe check you can try

1. Turn the heat pump off by leaving the unit in electric mode if you can, or leave it alone. 2. Clean the air filter. 3. Clear the area around the unit so air moves freely. 4. Arrange service; do not keep restarting the heat pump.

! Why to stop there
  • Over-limit temperatures can come from poor airflow, a sensor reading, or the refrigerant circuit.
  • We check airflow and sensor accuracy before conclusions about the sealed system.
  • We compare the reported temperature with a probe on the line before blaming the sealed circuit.
Opening a panel yourself does not automatically cancel a manufacturer warranty, but it can cause accidental damage, and some manufacturers set their own service conditions. Check your warranty terms, or ask us, before deciding.
→Same appliance

Other Water Heater codes

Dirty Filter (F14)GE GeoSpring First-Generation GEH50DEED Code Dirty Filter (F14): Clean the filter F15GE GeoSpring First-Generation GEH50DEED Code F15: DataFlash memory error Attention! Tank not filled!GE GeoSpring GEH50DNSRSA Message "Attention! Tank not filled!": Fill before power Heat Pump FailureGE GeoSpring GEH50DXSRGA Message "Heat Pump Failure": Heat pump section problem Water Heater FailureGE GeoSpring GEH50DNSRSA Message "Water Heater Failure": Electric side problem System FailureGE GeoSpring GEH50DXSRGA Message "System Failure": Immediate attention Wiring to unit incorrectGE GeoSpring GEH50DNSRSA Message "Wiring to unit incorrect. Must be 240V not 120V": Supply check EPGE GeoSpring GEH50DXSRGA Code EP: Energy price signal
F-EF-E questions
Is F-E dangerous?

It is a protection response, not a leak or fire warning. Still, repeated restarts under high temperature are not good for the compressor, so stop retrying and call us.

Why would the compressor run hot?

Restricted airflow, a dirty filter, a fan problem or refrigerant flow trouble can all do it. We test each of these in turn rather than guessing at the sealed system.

Can I keep showering?

Often yes, since the electric elements can cover it. Recovery will be slower and costlier until the heat pump is repaired, so tell us if you run short of hot water.

Book a visit

Still seeing F-E?

A technician diagnoses it on site and gives you the price in writing before any work starts.

(713) 547-5545