Booking today · Houston service windows 9–12 · 1–4 · 4–7 Independent GE specialists · Licensed & insured Mon–Fri 7:00 AM - 8:00 PM · Sat 8:00 AM - 6:00 PM
(713) 547-5545 Arrange a Repair
Error code · Microwave & Advantium

GE Advantium Message “Oven is Cooling”: Cool-Down After Speedcook

On GE Profile Advantium speedcook ovens, both 120 V and 240 V models such as the PSA2201RSS, PSB9120SFSS and PSB9240SFSS, two messages tell you the oven is cooling. Oven is too hot for sensor cook means…

Low risk · DIY check OK
Arrange a Repair(713) 547-5545
Code
Oven is too hot for sensor cook
Appliance
Microwave & Advantium
Brand
GE
Warranty
30-day workmanship

What Oven is too hot for sensor cook means

On GE Profile Advantium speedcook ovens, both 120 V and 240 V models such as the PSA2201RSS, PSB9120SFSS and PSB9240SFSS, two messages tell you the oven is cooling. Oven is too hot for sensor cook means that after speedcooking the oven must cool before the sensor works. Oven is Cooling means the cooling fan runs after cooking until internal parts cool. Both are normal and nothing is wrong.

Common causes of Oven is too hot for sensor cook

  • Oven still hot after a speedcook cycle
  • Cooling fan running after cooking
  • Sensor program chosen too soon
✓ One safe check you can try

1. Wait for the oven to cool. 2. Or cook by time instead of using the sensor program. 3. Let the cooling fan finish; do not switch off the power to the oven while it runs. 4. Try the sensor program again once the message is gone.

! Why to stop there
  • If the fan runs far longer than usual, whether a temperature sensor is reading wrong stays unknown
  • We check the sensors and the fan; ordinary cooling after a speedcook is not a repair
Opening a panel yourself does not automatically cancel a manufacturer warranty, but it can cause accidental damage, and some manufacturers set their own service conditions. Check your warranty terms, or ask us, before deciding.
→Same appliance

Other Microwave & Advantium codes

F1, F2, F3, F4GE Advantium Code F1, F2, F3, F4: Sensor and Touch Pad Circuits F3GE Profile Microwave Code F3: Key Held Over 60 Seconds ERR / SENSOR ERRORGE Microwave Message "SENSOR ERROR": Steam Not Detected SENSOR ERRORGE Advantium Message "SENSOR ERROR": Food Does Not Match Program LOC / LOCKEDGE Microwave Message "LOC": Control Lock-Out On FOOD / Insert FoodGE Microwave Message "Insert Food": Door Not Opened Cool / -90 / -80GE Microwave Message "Cool": Probe Temperature Below 90 Degrees Use ProbeGE Convection Microwave Message "Use Probe": Probe Not Detected
Oven is too hot for sensor cookOven is too hot for sensor cook questions
Why does my Advantium say Oven is Cooling?

After cooking, the fan keeps running until the internal parts cool, and the message shows while it does. It ends by itself, so there is nothing you need to press.

Why can't I use sensor cook right away?

The sensor needs a cooler oven to work. After speedcooking, wait for the cool-down or cook by time, and the sensor program will be available again afterward.

Are there other normal Advantium prompts like this?

Yes. Messages such as Optimizing Cooktime, Turn food over and Check for doneness are also normal prompts, not errors, and each simply asks you to wait or take a small action.

Book a visit

Still unsure about Oven is too hot for sensor cook?

A technician diagnoses it on site and gives you the price in writing before any work starts.

(713) 547-5545