Booking today · Houston service windows 9–12 · 1–4 · 4–7 Independent GE specialists · Licensed & insured Mon–Fri 7:00 AM - 8:00 PM · Sat 8:00 AM - 6:00 PM
(713) 547-5545 Arrange a Repair
Error code · Water Heater

GE GeoSpring GEH50/GEH80 Code F3: Compressor Failure

On the older GE GeoSpring hybrid electric water heaters, models GEH50DEEJ, GEH50DFEJ, GEH80DEEJ and GEH80DFEJ built around 2014 to 2016, F3 is listed as a compressor failure. The compressor is the sealed pump at the heart…

High · stop use, call now
Arrange a Repair(713) 547-5545
Code
F3
Appliance
Water Heater
Brand
GE
Warranty
30-day workmanship

What F3 means

On the older GE GeoSpring hybrid electric water heaters, models GEH50DEEJ, GEH50DFEJ, GEH80DEEJ and GEH80DFEJ built around 2014 to 2016, F3 is listed as a compressor failure. The compressor is the sealed pump at the heart of the heat pump. When the control finds it not running as expected, the heat pump stops and the electric elements carry the load. You may notice no compressor sound, slow heating, and higher power use.

Common causes of F3

  • Compressor start or run circuit
  • Wiring or relay to the compressor
  • Compressor itself
  • Refrigerant circuit condition
✓ One safe check you can try

1. Take a photo of the display and the label with the full model number. 2. Make sure the air inlet and outlet are clear. 3. Do not open the housing. 4. Use the electric elements for hot water, and call us to check the compressor circuit.

! Why to stop there
  • Compressor failures can come from the circuit around it or from the compressor itself.
  • We test the circuit first.
  • A compressor repair on a unit this age is quoted in writing, with an honest view.
Opening a panel yourself does not automatically cancel a manufacturer warranty, but it can cause accidental damage, and some manufacturers set their own service conditions. Check your warranty terms, or ask us, before deciding.
→Same appliance

Other Water Heater codes

F5, F6, F7, F8GE GeoSpring First-Generation GEH50DEED Codes F5-F8: Sensor failures F9GE GeoSpring First-Generation GEH50DEED Code F9: Bottom element problem F10GE GeoSpring First-Generation GEH50DEED Code F10: Top element problem F11GE GeoSpring First-Generation GEH50DEED Code F11: Tank must be filled bAd linE (F12)GE GeoSpring First-Generation GEH50DEED Code bAd linE (F12): Supply voltage low F13GE GeoSpring First-Generation GEH50DEED Code F13: Keypad key stuck Dirty Filter (F14)GE GeoSpring First-Generation GEH50DEED Code Dirty Filter (F14): Clean the filter F15GE GeoSpring First-Generation GEH50DEED Code F15: DataFlash memory error
F3F3 questions
How is F3 related to F14?

The idea is related, but F3 is on the older GEH50 and GEH80 series, and F14 is on the newer PF and PH series. The two lists are kept separate.

Is there any hot water in the meantime?

Not as much as usual. The electric elements can heat the tank, at a higher running cost, and recovery after heavy use may be slower until the heat pump runs again.

Is it worth repairing?

It depends on the cause and the age of the unit. We give you a written price and an honest view before you decide, and the work carries our 30-day warranty.

Book a visit

Still seeing F3?

A technician diagnoses it on site and gives you the price in writing before any work starts.

(713) 547-5545