Booking today · Houston service windows 9–12 · 1–4 · 4–7 Independent GE specialists · Licensed & insured Mon–Fri 7:00 AM - 8:00 PM · Sat 8:00 AM - 6:00 PM
(713) 547-5545 Arrange a Repair
Error code · Dishwasher

GE Dishwasher Start Light Flashing: Door Opened or Cycle Interrupted

On GE and GE Profile electronic dishwashers from 2014 on, such as the GDT665, GDT630, GDF630, GDT226 and PDT715, a flashing Start light means the door was opened or the cycle was interrupted. The dishwasher is…

Low risk · DIY check OK
Arrange a Repair(713) 547-5545
Code
Start light flashing
Appliance
Dishwasher
Brand
GE
Warranty
30-day workmanship

What Start light flashing means

On GE and GE Profile electronic dishwashers from 2014 on, such as the GDT665, GDT630, GDF630, GDT226 and PDT715, a flashing Start light means the door was opened or the cycle was interrupted. The dishwasher is waiting for you to restart it. On older models, a Start or Reset light that blinks for 75 to 90 seconds after a reset means the control is turning itself off.

Common causes of Start light flashing

  • Door opened during the cycle
  • Door not fully latched at start
  • Cycle interrupted by a power blip
✓ One safe check you can try

1. Close the door firmly until it latches. 2. Press Start once and close the door within 4 seconds. 3. Press Start a second time only if you want to cancel the cycle while it runs. 4. If the light keeps flashing with the door shut, stop and let us check the latch.

! Why to stop there
  • If the door is shut and latched and the light still flashes, we test the door latch switch circuit.
  • We check the strike alignment, since a door that looks closed can still be slightly off.
  • You get a written price first, and our repair has a 30-day workmanship warranty.
Opening a panel yourself does not automatically cancel a manufacturer warranty, but it can cause accidental damage, and some manufacturers set their own service conditions. Check your warranty terms, or ask us, before deciding.
→Same appliance

Other Dishwasher codes

Smart Assist light redGE Dishwasher Smart Assist Light Red: A Potential Problem Was Detected Smart Assist light yellowGE Dishwasher Smart Assist Light Yellow: A Notification Is Waiting in SmartHQ Low Rinse AidGE Dishwasher Low Rinse Aid Indicator: Refill the Dispenser nH (Delay Start)GE Dishwasher Display nH: Delay Start Counting Down PFGE Dishwasher Code PF: Power Failure Noted by the Control 999GE Dishwasher Code 999: Possible Leak, or a Control Reset PrSGE Electronic Dishwasher Code PrS: Sensor for Water Pressure Sends Invalid Signal C1GE Electronic Dishwasher Code C1: Drain Step Ran Past 2 Minutes
Start light flashingStart light flashing questions
Why is the Start light flashing on my GE dishwasher?

The door was opened or the cycle was interrupted, so the dishwasher is waiting for you. Close the door fully until it latches, then press Start once to resume the cycle.

What if I press Start twice?

Pressing Start a second time while the dishwasher is running cancels the cycle. To resume after an interruption, press it once and close the door within four seconds.

Why does the light blink after a reset on my older GE?

On older models, a Start or Reset light blinking for 75 to 90 seconds after a reset means the control is turning off. Let it finish before restarting.

Book a visit

Still unsure about Start light flashing?

A technician diagnoses it on site and gives you the price in writing before any work starts.

(713) 547-5545