Booking today · Houston service windows 9–12 · 1–4 · 4–7 Independent GE specialists · Licensed & insured Mon–Fri 7:00 AM - 8:00 PM · Sat 8:00 AM - 6:00 PM
(713) 547-5545 Arrange a Repair
Error code · Microwave & Advantium

GE Microwave Code F10: Touch Screen Reads as Shorted

On GE and Profile microwaves, including over-the-range and countertop models such as the JVM3160, JVM7195, JES1657 and PVM9179 series, F10 reports that the touch screen is shorted. The control sees the screen as pressed or electrically…

Medium · inspection needed
Arrange a Repair(713) 547-5545
Code
F10
Appliance
Microwave & Advantium
Brand
GE
Warranty
30-day workmanship

What F10 means

On GE and Profile microwaves, including over-the-range and countertop models such as the JVM3160, JVM7195, JES1657 and PVM9179 series, F10 reports that the touch screen is shorted. The control sees the screen as pressed or electrically bridged, so it cannot read your commands. You will see F10 on the display, and the microwave may ignore touches, beep on its own or stay locked out. Moisture or a worn screen layer are common reasons for this behavior, though the code only identifies the circuit.

Common causes of F10

  • Touch screen layer shorted internally
  • Moisture or grease reaching the screen
  • Ribbon connector between the screen and the control loose
  • Control board misreading the screen
✓ One safe check you can try

1. Wipe the screen with a dry soft cloth and keep it away from steam and spills. 2. Turn the circuit breaker or fuse off for 30 seconds and restore it. 3. Wait a minute and try touching a pad. 4. If F10 comes back, stop using the microwave and book a visit.

! Why to stop there
  • A dry screen that still shows F10 points to the screen or its connector.
  • We test the screen and control before replacing a part.
  • A written price comes first.
Opening a panel yourself does not automatically cancel a manufacturer warranty, but it can cause accidental damage, and some manufacturers set their own service conditions. Check your warranty terms, or ask us, before deciding.
→Same appliance

Other Microwave & Advantium codes

TurnGE Microwave Message "Turn": Turn Food Over OVEN TOO HOT FOR USING ALTERNATE METHODGE Profile Microwave Message "OVEN TOO HOT FOR USING ALTERNATE METHOD": Cavity Above 200°F Oven is too hot for sensor cookGE Advantium Message "Oven is Cooling": Cool-Down After Speedcook Optimizing CooktimeGE Advantium Message "Optimizing Cooktime": Voltage Check HOTGE Convection Microwave Display Says HOT: Cavity Still Warm After Baking Reset Filter lightGE Over-the-Range Microwave Reset Filter Light: Six-Month Charcoal Reminder SENSOR ERROR - PLEASE CLEARGE Café Drawer Microwave Message "SENSOR ERROR - PLEASE CLEAR" or "KEYPAD SHORTED" Wireless icon solid on displayGE Smart Microwave Wireless Icon Solid: SmartHQ Setup Status
F10F10 questions
What does F10 mean on my microwave?

The touch screen is shorted, so the control cannot read the pads normally. You may see no response, or the microwave may act on its own. The code names the screen circuit, not a part.

Can moisture cause F10?

Yes, steam or spills can bridge the screen. Dry it gently, then try a power reset. If the code returns, the screen needs testing. Avoid spraying cleaner onto it.

How does F10 differ from F3?

F10 is about the touch screen, while F3 is about the touch pad panel. Which one your microwave shows depends on its control style. Both are tested at the control.

Book a visit

Still seeing F10?

A technician diagnoses it on site and gives you the price in writing before any work starts.

(713) 547-5545