Booking today · Houston service windows 9–12 · 1–4 · 4–7 Independent GE specialists · Licensed & insured Mon–Fri 7:00 AM - 8:00 PM · Sat 8:00 AM - 6:00 PM
(713) 547-5545 Arrange a Repair
Error code · Washer

GE UltraFresh Washer Code 35 to 64: Accelerometer Board Problem

The numbers 35, 59, 60, 61, 63 and 64 are accelerometer records on GE UltraFresh front-load washers (GFW510, GFW550, GFW650 and GFW850 series, 2020 and newer). The control sets them when the accelerometer board, which senses…

Medium · inspection needed
Arrange a Repair(713) 547-5545
Code
35, 59, 60, 61, 63, 64
Appliance
Washer
Brand
GE
Warranty
30-day workmanship

What 35, 59, 60, 61, 63, 64 means

The numbers 35, 59, 60, 61, 63 and 64 are accelerometer records on GE UltraFresh front-load washers (GFW510, GFW550, GFW650 and GFW850 series, 2020 and newer). The control sets them when the accelerometer board, which senses drum motion and imbalance, reports a problem. A technician reads them in the stored error history, and the display on these models may also show them. Owners may see unusual shaking, spin cycles cut short or a washer that limits its speed.

Common causes of 35, 59, 60, 61, 63, 64

  • Accelerometer board and its connector
  • Wiring between the sensor board and the main control
  • Mounting of the sensor to the cabinet
  • Main control reading of the sensor
✓ One safe check you can try

1. Level the washer so all four feet touch the floor and it does not rock. 2. Run a small, evenly spread load and see whether the spin behaves normally. 3. Leave the cabinet closed; the sensor board is not an owner repair.

! Why to stop there
  • A sensor board that reports a problem may be failing, loose or wrongly mounted, and the number alone does not decide
  • We check the board mounting and wiring, then test the signals the control receives
  • You see a written price before any part is replaced, with a 30-day workmanship warranty
Opening a panel yourself does not automatically cancel a manufacturer warranty, but it can cause accidental damage, and some manufacturers set their own service conditions. Check your warranty terms, or ask us, before deciding.
→Same appliance

Other Washer codes

Load RebalancingGE Front-Load Washer Message "Load Rebalancing": Washer Is Correcting an Uneven Load A problem has been detectedGE Profile Harmony Washer Message "A problem has been detected with this unit": Electronics Alert 70GE UltraFresh Washer Code 70: Inverter Start-Up Repeats 78GE UltraFresh Washer Code 78: Board Software Mismatch 85GE UltraFresh Washer Code 85: Voltage Out of Range Door / doorGE UltraFresh Washer Message "Door": Open the Door Before the Next Cycle LidGE Top-Load Washer Message "Lid": Open and Close the Lid to Continue Lid Locked light flashingGE Top-Load Washer Lid Locked Light Flashing: Three Cycles, No Lid Opened
35, 59, 60, 61, 63, 6435, 59, 60, 61, 63, 64 questions
What does the accelerometer do?

It senses drum motion so the control can detect imbalance and limit spin. If it misreports, spins may be cut short or the washer may shake.

Is it the same as a bad load?

No. A bunched load is a laundry matter; these numbers point to the sensor board. The sensor reads motion, so a washer that is rocking on its feet can look like a sensor problem and is worth leveling first.

Does a shaking washer mean this code?

Not always. A washer that is out of level or has a bunched load shakes too. We rule those out before testing the sensor board.

Book a visit

Still seeing 35, 59, 60, 61, 63, 64?

A technician diagnoses it on site and gives you the price in writing before any work starts.

(713) 547-5545