Booking today · Houston service windows 9–12 · 1–4 · 4–7 Independent GE specialists · Licensed & insured Mon–Fri 7:00 AM - 8:00 PM · Sat 8:00 AM - 6:00 PM
(713) 547-5545 Arrange a Repair
Error code · Washer

GE Top-Load Washer Message “bALAnCINg”: Load Is Uneven in the Tub

On GE top-load washers with a display from 2015 on, such as the GTW720 and the Profile PTW600, bALAnCINg means the washer cannot spin properly because the load is no longer evenly distributed in the tub.…

Low risk · DIY check OK
Arrange a Repair(713) 547-5545
Code
bALAnCINg
Appliance
Washer
Brand
GE
Warranty
30-day workmanship

What bALAnCINg means

On GE top-load washers with a display from 2015 on, such as the GTW720 and the Profile PTW600, bALAnCINg means the washer cannot spin properly because the load is no longer evenly distributed in the tub. It usually appears with the SPIN light flashing. The washer stops short of a full-speed spin to protect itself, so you may find clothes wetter than normal and a heavy lump of fabric on one side of the drum.

Common causes of bALAnCINg

  • Bulky or single heavy item pushed to one side
  • Mixed load of towels and light clothing
  • Washer not sitting level on the floor
✓ One safe check you can try

1. Open the lid and spread the clothes out evenly around the tub. 2. Take out or add items so the load is not one big bundle. 3. Press Start, or select Drain & Spin and press Start. 4. If it repeats with a normal load, check that the washer does not rock on the floor.

! Why to stop there
  • A balanced load that still triggers the message makes us check that the washer is level and the feet are firm.
  • We look at the suspension and the lid area when the drum moves more than it should.
  • We write the price before work begins, and our repair carries a 30-day workmanship warranty.
Opening a panel yourself does not automatically cancel a manufacturer warranty, but it can cause accidental damage, and some manufacturers set their own service conditions. Check your warranty terms, or ask us, before deciding.
→Same appliance

Other Washer codes

A problem has been detectedGE Profile Harmony Washer Message "A problem has been detected with this unit": Electronics Alert 70GE UltraFresh Washer Code 70: Inverter Start-Up Repeats 78GE UltraFresh Washer Code 78: Board Software Mismatch 85GE UltraFresh Washer Code 85: Voltage Out of Range Door / doorGE UltraFresh Washer Message "Door": Open the Door Before the Next Cycle LidGE Top-Load Washer Message "Lid": Open and Close the Lid to Continue Lid Locked light flashingGE Top-Load Washer Lid Locked Light Flashing: Three Cycles, No Lid Opened Fill light blinkingGE Top-Load Washer Fill Light Blinking: Two Blinks for No Water, Three for Open Lid
bALAnCINgbALAnCINg questions
Why does my GE washer say bALAnCINg?

The load shifted to one side and the drum cannot spin at speed. Redistribute the clothes evenly and run Drain & Spin. It is a load issue far more often than a washer issue.

Is bALAnCINg the same as the flashing Spin light?

It is the display version. A flashing Spin light on its own is covered separately, while this text appears on display models with the Spin light flashing along with it.

Does a single comforter cause this?

Often, yes. One large item can ball up on one side. Mix in a few towels or wash it with fewer items so the weight spreads around the drum.

Book a visit

Still unsure about bALAnCINg?

A technician diagnoses it on site and gives you the price in writing before any work starts.

(713) 547-5545