Booking today · Houston service windows 9–12 · 1–4 · 4–7 Independent GE specialists · Licensed & insured Mon–Fri 7:00 AM - 8:00 PM · Sat 8:00 AM - 6:00 PM
(713) 547-5545 Arrange a Repair
Error code · Washer

GE UltraFresh Washer Code 27: Inverter Overheated, Motor Stopped

Code 27 on GE UltraFresh front-load washers (GFW510, GFW550, GFW650 and GFW850 series, 2020 and newer) means the inverter, the board that drives the motor, reported a temperature above 221 degrees F for five seconds. The…

High · stop use, call now
Arrange a Repair(713) 547-5545
Code
27
Appliance
Washer
Brand
GE
Warranty
30-day workmanship

What 27 means

Code 27 on GE UltraFresh front-load washers (GFW510, GFW550, GFW650 and GFW850 series, 2020 and newer) means the inverter, the board that drives the motor, reported a temperature above 221 degrees F for five seconds. The control stops the motor to protect the drive. The stored error history holds the number for a technician, and on these models the display can show it too. You may see a cycle that stops mid-wash or spin, a warm cabinet, or a washer that will not restart right away.

Common causes of 27

  • Heavy or jammed drum making the motor work harder
  • Inverter board cooling or ventilation around the cabinet
  • Motor drive circuit running hot
  • Wiring or connectors at the drive
✓ One safe check you can try

1. Stop the cycle and let the washer sit with the door open so the cabinet can cool. 2. Make sure nothing is stacked against the washer and air can move around the back and sides. 3. If you smell hot or burning plastic, unplug it and call us.

! Why to stop there
  • Whether the heat came from a heavy load, poor airflow or the drive itself stays unknown until it is checked
  • We check the drum for drag, the airflow around the washer and the drive circuit
  • The price is written and approved before work starts, with a 30-day workmanship warranty
Opening a panel yourself does not automatically cancel a manufacturer warranty, but it can cause accidental damage, and some manufacturers set their own service conditions. Check your warranty terms, or ask us, before deciding.
→Same appliance

Other Washer codes

Fill light blinkingGE Top-Load Washer Fill Light Blinking: Two Blinks for No Water, Three for Open Lid Wash and Rinse lights blinkingGE Spacemaker Washer Wash and Rinse Lights Blinking: Water Not Entering Two furthest lights flashingGE Top-Load Washer Two Furthest Lights Flashing: General Cycle Error PoGE Top-Load Washer Message "Po": Slow to Pump Out the Water bALAnCINgGE Top-Load Washer Message "bALAnCINg": Load Is Uneven in the Tub CLrFLtrGE Compact Washer Message "CLrFLtr": Drain Pump Filter Needs Cleaning Load RebalancingGE Front-Load Washer Message "Load Rebalancing": Washer Is Correcting an Uneven Load A problem has been detectedGE Profile Harmony Washer Message "A problem has been detected with this unit": Electronics Alert
2727 questions
Is it safe to restart after it cools?

A single stop with a heavy load may not repeat, but if the code returns or you smell heat, stop using it. Repeated overheating can damage the drive.

Could my load size matter?

Yes. A packed drum makes the motor work harder, which can add heat. Try a lighter load once cool. Heat that returns on lighter loads is more worrying, because it points away from the laundry and toward the drive or airflow.

Where does the heat come from?

Usually from the motor drive working hard against a heavy drum, poor airflow or a weak drive board. We test each in turn rather than guessing.

Book a visit

Still seeing 27?

A technician diagnoses it on site and gives you the price in writing before any work starts.

(713) 547-5545