Booking today · Houston service windows 9–12 · 1–4 · 4–7 Independent GE specialists · Licensed & insured Mon–Fri 7:00 AM - 8:00 PM · Sat 8:00 AM - 6:00 PM
(713) 547-5545 Arrange a Repair
Error code · Washer

GE UltraFresh Code Fault 1 Lock Monitor: motor spinning while door unlocked

On GE UltraFresh front-load washers in the GFW510, GFW550, GFW650 and GFW850 series, Fault 1 Lock Monitor means the control saw the motor shaft spinning above 45 RPM for 5 seconds in spin mode while the…

High · stop use, call now
Arrange a Repair(713) 547-5545
Code
Fault 1 Lock Monitor
Appliance
Washer
Brand
GE
Warranty
30-day workmanship

What Fault 1 Lock Monitor means

On GE UltraFresh front-load washers in the GFW510, GFW550, GFW650 and GFW850 series, Fault 1 Lock Monitor means the control saw the motor shaft spinning above 45 RPM for 5 seconds in spin mode while the door was unlocked. The washer should never spin with an unlocked door, so it stops. This is a technician-level message normally shown only in a technician-level display mode. You may see a halted spin or the cycle ending early.

Common causes of Fault 1 Lock Monitor

  • Door lock not reporting that it is locked
  • Wiring between the lock and the control
  • Motor speed reading while the door shows unlocked
  • Control board reading the lock signal
✓ One safe check you can try

1. Do not open the door while the drum is turning. 2. Wait until the drum has stopped completely. 3. Close the door firmly and run a short drain and spin. 4. If the message returns, stop using the washer and call us.

! Why to stop there
  • The control compares door lock and motor speed signals, and the code does not say which side is wrong.
  • We test the lock signal and the motor reading under the same cycle.
  • A spinning drum with an unlocked door is a safety concern, so we do not suggest workarounds.
Opening a panel yourself does not automatically cancel a manufacturer warranty, but it can cause accidental damage, and some manufacturers set their own service conditions. Check your warranty terms, or ask us, before deciding.
→Same appliance

Other Washer codes

70GE UltraFresh Washer Code 70: Inverter Start-Up Repeats 78GE UltraFresh Washer Code 78: Board Software Mismatch 85GE UltraFresh Washer Code 85: Voltage Out of Range Door / doorGE UltraFresh Washer Message "Door": Open the Door Before the Next Cycle LidGE Top-Load Washer Message "Lid": Open and Close the Lid to Continue Lid Locked light flashingGE Top-Load Washer Lid Locked Light Flashing: Three Cycles, No Lid Opened Fill light blinkingGE Top-Load Washer Fill Light Blinking: Two Blinks for No Water, Three for Open Lid Wash and Rinse lights blinkingGE Spacemaker Washer Wash and Rinse Lights Blinking: Water Not Entering
Fault 1 Lock MonitorFault 1 Lock Monitor questions
What does Lock Monitor mean in plain words?

It is a safety check. The control saw the motor spinning fast while the door appeared to be unlocked, which is never allowed during a spin. The washer stops the spin to protect you and the machine.

Can I keep using the washer?

We suggest not using it until it has been checked. A door that does not lock during spin is not something to ignore, and repeated spins could make the underlying problem worse.

Where did I see this message?

It is a technician-level message shown only in a technician-level display mode. If it appeared, tell us exactly what you saw and when it happened, and we use that to decide where to begin our testing.

Book a visit

Still seeing Fault 1 Lock Monitor?

A technician diagnoses it on site and gives you the price in writing before any work starts.

(713) 547-5545