Booking today · Houston service windows 9–12 · 1–4 · 4–7 Independent GE specialists · Licensed & insured Mon–Fri 7:00 AM - 8:00 PM · Sat 8:00 AM - 6:00 PM
(713) 547-5545 Arrange a Repair
Error code · Washer

GE Washer Spin Light Blinking: load out of balance

On GE electronic-control washers from 2017 onward, a blinking Spin light means the washer detected an out-of-balance load. It corrects the imbalance on its own and continues, but it may not reach full spin speed. You…

Low risk · DIY check OK
Arrange a Repair(713) 547-5545
Code
Spin Light Blinking
Appliance
Washer
Brand
GE
Warranty
30-day workmanship

What Spin Light Blinking means

On GE electronic-control washers from 2017 onward, a blinking Spin light means the washer detected an out-of-balance load. It corrects the imbalance on its own and continues, but it may not reach full spin speed. You may find clothes wetter than normal at the end of the cycle. This is a load issue much more often than a repair issue.

Common causes of Spin Light Blinking

  • Load bunched on one side of the tub
  • Single heavy item such as a rug or comforter
  • Washer not level on the floor
✓ One safe check you can try

1. If the load is wetter than normal, open the lid and spread the laundry evenly. 2. Run Drain and Spin or Spin. 3. Wash bulky items in smaller loads. 4. Check that the washer sits level and does not rock. 5. If the Spin light keeps blinking, call us.

! Why to stop there
  • If the load is evenly spread and the light still blinks, a level or suspension issue may be involved.
  • We check that the washer sits level and the drum moves freely.
  • We recommend not overloading in the meantime.
Opening a panel yourself does not automatically cancel a manufacturer warranty, but it can cause accidental damage, and some manufacturers set their own service conditions. Check your warranty terms, or ask us, before deciding.
→Same appliance

Other Washer codes

CLrFLtrGE Compact Washer Message "CLrFLtr": Drain Pump Filter Needs Cleaning Load RebalancingGE Front-Load Washer Message "Load Rebalancing": Washer Is Correcting an Uneven Load A problem has been detectedGE Profile Harmony Washer Message "A problem has been detected with this unit": Electronics Alert 70GE UltraFresh Washer Code 70: Inverter Start-Up Repeats 78GE UltraFresh Washer Code 78: Board Software Mismatch 85GE UltraFresh Washer Code 85: Voltage Out of Range Door / doorGE UltraFresh Washer Message "Door": Open the Door Before the Next Cycle LidGE Top-Load Washer Message "Lid": Open and Close the Lid to Continue
Spin Light BlinkingSpin Light Blinking questions
Why is my Spin light blinking?

The washer detected an out-of-balance load. It tries to correct the imbalance on its own and carry on, but it may not reach full spin speed, so clothes can come out wetter than usual.

How do I fix it?

Open the lid, spread the laundry evenly around the drum, and run Drain and Spin or Spin. Wash bulky items like comforters in smaller loads, which makes the washer much less likely to go out of balance.

It keeps blinking with small loads. Why?

The washer may not be level, or something inside may be affecting how the drum moves. We check the leveling and the drum motion, and give you a written price before any repair.

Book a visit

Still unsure about Spin Light Blinking?

A technician diagnoses it on site and gives you the price in writing before any work starts.

(713) 547-5545